Push Modules
Explanation of EZ Tools Interface
The VMS process uses the EZ Tools for specific pieces of information Get IP Check not an LR series Camera (needs ONVIF connection, not P&P) Check Firmware Get the Registration code when needed after P&P Module added
Preparing a Camera for Push Module Addition
Preparing any Camera for the addition of P&P Modules is quite simple. You require to: Unpack the Camera from the box Have access to a Powered Switch, Plug Camera into Switch using POE cable Ensure the Switch is plugged into a Router using a POE Cable ...
Hikvision: List of Supported Models
R2 R4 Fisheye R4 Multi Sensor R4 R6 G1 Fisheye G1 G0 Wi-Fi G0 H3 DS-2CD2010-I DS-2CD4025FWD-(A)(P) DS-2CD6332FWD-I(V)(S) DS-2CD6986F-(H) DS-2CD2F22FWD-I(W)(S) DS-2CD2025FWD-I DS-2CD2935FWD-I(S) DS-2CD2041G1-IDW1 DS-2CD2347G3E-L DS-2CD5A26G0-IZ(H)S ...
How to install Push Module: Axis Cameras
Almost all Axis cameras can be added using our custom built push module! Depending on the camera's main chip a different version of the push module should be used. To download model-specific push module please visit: Axis Camera Push Module from your ...
Axis Camera Push Modules
Depending on the camera model and architecture a different version of the push module will be available. Instructions to determine the correct version of the push module for your camera can be found: determine camera architecture for axis cameras in ...
How to Determine Camera Architecture for Axis Cameras
In order to determine which Push Module to use for your Axis Camera, you will need to determine the Camera Architecture. For newer Axis cameras go to System=>Plain Config Scroll down to Properties option: And look for System section and ...
Installing Push Module for Uniview cameras - RETIRED
Instruction for Push Installer Application. 1. Determine which firmware your camera has 2. Download and install the Push Installer application 3. Update your camera to the latest stable firmware version 4. Enable Debug mode 5. Install push module ...
How to Add Push Module to Tiandy Cameras
To add a push module to the Tiandy camera please update the camera with the firmware that has a preinstalled push module. Step 1: Download firmware with a preinstalled push module. Navigate to: Tiandy Firmwares with Pre-Installed Push Module in your ...
Adding your Push Module Camera to your Customer
Once you have added our push module to your camera, you can follow the steps below to add the camera to the cloud platform. Navigate to vmsadmin.localsecurity.org Log in using your previously created credentials (Ask your Integrator or Account ...
Milesight Firmware with Embeded Push Module
To activate the push module on Milesight cameras please download model specific firmware from the table below and upgrade your camera using it. All 40 series cameras use the same firmware so the same file can be used for all models that belong to the ...
Local Security Push Module Overview
Local Security has a unique PUSH Module solution, allowing cameras to connect directly to the cloud and avoid security vulnerabilities. This is our simple Plug&Play setup where customers only need to plug a camera into a router and it makes the cloud ...
Adding our Push Module to a Milesight Camera
To activate the push module on your Milesight cameras, please download the push enabled firmware and upgrade your camera using it. To see a list of available push modules for Milesight cameras navigate to: Milesight Firmware with Embedded Push Module ...
Uniview Models Compatible with Push Module Installer
Download and Install Guide: Uniview Push Module Installer Uniview Compatibility List Your device may be compatible even if it is not on the list. Please contact us if you have a device that does not appear on the list. C1L-2WN IPC2122LB-DSF28KM ...
How to add our Push Module to Vivotek Cameras
Step 1: Connect to the camera. Connect the camera to the network and identify its IP address using Vivotek Installation Wizard. Double click on the camera to open the web interface page in your browser. Step 2: Configure Network settings. Make sure ...
Uniview Push Module Installer
Uniview Compatibility List Your device may be compatible even if it is not on the list. Please contact us if you have a device that does not appear on the list. C1L-2WN IPC2122LB-DSF28KM IPC2122LB-DSF40KM IPC2122LR3-F40-E IPC2122LR3-PF28M-D ...
Hikvision Push Modules and Firmware
Push modules are available for the following Hikvision camera series: Series Firmware Push module G0 download download G1 download download R2 download download R4 download download R6 download download You can use this list to determine the model ...
What are Plug and Play servers?
Local Security's P&P solution is based on our own technologies. We do not use any of the manufacturer plug and plug features but instead we add our own module into the camera. Through this we create a direct encrypted tunnel between the camera and ...
Push Module Compatibility List for Uniview Cameras
Take note that this list is ever changing and growing with our industry, please bring any inquiries to us if you are ever unsure. Let's start by checking your camera's MODEL and FIRMWARE VERSION and compare it against what solutions we have available ...
Tiandy Firmwares with Pre-Installed Push Modules
To activate the push module on Tiandy cameras please download model specific firmware from the table below and upgrade your camera using it. For detailed instruction please visit: How to Add Push Module to Tiandy Cameras Model Download Link TC-C32KN ...
What are the Camera Manufacturers you have the Push Module Solution With?
Axis, Uniview, Vivotek, Hikvision, TVT, Sunell, Tiandy
How to Install Push Module: Hikvision Cameras
Make sure that your camera has the latest firmware! Take note only: R2, R4, R6, G0 and G1 series are supported. For full compatibility chart navigate to: List of Supported Models from your knowledge base If the camera was used before or the factory ...